Your shopping cart is empty.
Polymer based Hold coating product, Easy to apply on SHIP HOLD SURFACE. Slip Barrier Coats HOLD BLOCK is POLYMER BASED non-reactive coating materials which makes thin film barrier on the surface after dry. Due to the formation of RXSOL THIN barrier film on the surface, the cleaning operation after unloading becomes quicker and easier with optimum results.
Before application, previous cargo residues should be completely removed, and the existing paint/coating on the surface should be properly cured.
Application guidance recommends using suitable low-pressure spraying equipment. Application should begin at the bottom of the bulkheads and proceed upward, followed by the tank sides and tank tops. The nozzle is positioned approximately half a metre from the surface during application.
The stated coverage is approximately 16–18 m² per litre, depending on application conditions and surface characteristics. After application, the coating should be allowed to dry completely before loading cargo. Typical drying time is approximately 1–2 hours, depending on temperature and humidity.
RXSOL HOLD BLOCK is a Heavy Duty protective Solution for hold of vessels , which carrying corrosive and / or messy cargos such as sulphur salt petcock coal and concentrates. It can be easily removed with it
General Recommendation Dose for smooth surface :
for Sulphur, Salt, etc 100 Ltrs/Hold for HANDYMAX & 150 Ltrs/Hold for PANAMAX
& for Petcoke, Coal, etc 200 Ltrs/Hold for HANDYMAX & 250 Ltrs/Hold for PANAMAX
This materials can be use directly with low pressure machine or manually by garden spray pump. in general practice on smooth & clean surface each drums of 210 ltrs covers 2000 to 2500 sq meter while on rough and rusted surface require more quantities of materials.
for HANDYMAX (5 Holds) : In general 500 Ltr to 1000 Ltr RXSOL-22-2210-210 require to cover area up to 12 mtrs , i.e approx 1/2 drum to 1 drum of material is sufficient for each hold , while
for PANAMAX (7 Holds) : In general 1000 Ltr to 2000 Ltrs RXSOL-22-2210-210 require to cover full area. , i.e approx 3/4 drum to 1.25 drums of material is sufficient for each hold.
Refer this link for complete set of HOLD CLEANING KIT ::: http://rxmarine.com/Ship-hold-cleaning-kit-set-supplier
This Emulsion is safe to use , But as a precaution goggles & Protective gloves with mask require before use of this materials.
Precaution : 1 > Deposition of previous cargo / Lime wash should be removed .
2 > Newly Painted surface should be fully cured.
Other Valuable Hold Cleaners :::
Cement Remover RX Hold ::: Highly concentrated and powerful penetrating agents materials which is effectively react with cement to loosen the bonding strength . Best results can obtain on dry surface of cement. RXSOL'S R & D has developed this molecular cement dissolver. Part No.- RXSOL-22-2202-025, Part No.- RXSOL-22-2202-020, Part No.- RXSOL-22-2202-050
Refer this link for complete set of HOLD CLEANING KIT ::: https://rxmarine.com/Ship-hold-cleaning-kit-set-supplier
PRELOAD 300
Ship hold protective layer coating chemicals. Polymer based water soluble Slip Barrier Polymer Coats HOLD BLOCK is easy to use. There is no any special technical method required to applied on hold surface. Simply dilute the Slip Barrier Polymer Coat with water and spread on entire hold area from top to bottom side. Extra liquidcoming towards bottom can be recollected to cover uncoated area. Simple spray method is helpfull to save time of application. NOTE - Before application of Slip Barrier Polymer Coat Hold Block clean entire hold surface area and make sure dust free.
Slip Barrier Polymer Coats HOLD BLOCK formulated to perform maximum protection to wards hold surface during transport and save lot of time during unloading operations as cargo doesn't adhere towards hold surface. After unloading of cargo when Aquaatuff High Foam is applied to Slip Barrier Polymer Coat treated hold surface all cargo residue get off without any extra manual force requirement.
RXSOL PRELOAD Slip HOLD BLOCK is a water-based, temporary protective coating designed for cargo hold surfaces on ships carrying difficult and corrosive bulk cargoes. It forms a thin, homogeneous, water-soluble film that helps protect cargo hold surfaces from cargo penetration, staining, corrosion, and contamination.
RXSOL PRELOAD Slip HOLD BLOCK is particularly useful before loading cargoes such as cement, sulphur, salt, petcoke, coal, and concentrates, where cargo residues can become difficult to remove and may affect the condition of the cargo hold.
PRELOAD Slip HOLD BLOCK is a temporary, water-based cargo hold barrier coating manufactured by RXSOL. When sprayed onto a properly prepared cargo hold and allowed to dry, it creates a thin protective film over the surface.
The film helps prevent small cargo particles from becoming trapped in surface pores and protects the underlying coating and metal surface from contact with aggressive or difficult-to-clean cargoes.
One of the key advantages of PRELOAD Slip HOLD BLOCK is that the protective film can be removed with water after cargo discharge, including cold seawater under pressure.
PRELOAD Slip HOLD BLOCK creates a temporary barrier between the cargo and cargo-hold surface. This can simplify post-cargo cleaning and help maintain the condition of the hold.
The product is designed to protect metal surfaces against contact with corrosive cargoes. This is particularly relevant when transporting cargoes such as salt, sulphur, coal, petcoke, and mineral concentrates.
The dried film is water soluble and can be removed after unloading without requiring aggressive chemical stripping in normal applications. The film can be removed using cold seawater under pressure.
4. Helps Prevent Cargo Penetration
The temporary film fills surface pores and helps prevent fine cargo particles from becoming trapped in the cargo-hold surface. It can also help protect paintwork against cargo penetration.
PRELOAD Slip HOLD BLOCK can be used on metal surfaces and metal alloys and is designed not to adversely affect rubber, plastic compounds, or cargo-hold coatings when properly applied.
PRELOAD Slip HOLD BLOCK is primarily used as a cargo hold protective coating on bulk carriers and other vessels transporting difficult-to-clean or potentially corrosive bulk cargo.
Typical cargoes include:
Cement
Sulphur
Salt
Petcoke
Coal
Mineral concentrates
Other difficult-to-clean bulk cargoes
The manufacturer specifically identifies these cargo types for PRELOAD Slip HOLD BLOCK application.
After unloading, the temporary protective film can be removed using water. The manufacturer's technical information states that cold seawater under pressure can be used for removal.
This water-removable characteristic can help reduce the effort required for cargo-hold preparation between voyages and may support faster hold-cleaning operations.
PRELOAD Slip HOLD BLOCK:
25 L plastic jerrican
210 L plastic drum
Cargoes such as cement, petcoke, coal, salt, sulphur, and mineral concentrates can leave stubborn residues or interact with cargo-hold surfaces. Applying a temporary barrier before loading can help reduce direct contact between the cargo and the hold surface.
The main operational benefits include:
Temporary protective barrier
Protection against difficult and corrosive cargoes
Reduced cargo penetration into surface pores
Easier post-discharge cleaning
Water-removable film
Suitable for bulk cargo operations
Simple spray application
Suitable for metal surfaces and compatible coatings when properly applied
For ship operators, ship managers, superintendents, and marine cleaning contractors, cargo hold preparation is an important part of maintaining vessel turnaround efficiency.
Using a temporary hold coating such as PRELOAD Slip HOLD BLOCK before loading selected bulk cargoes can help protect the cargo-hold surface and simplify subsequent cleaning operations. The product is specifically developd as a protective coating for cargo tanks/holds against corrosive cargoes.
PRELOAD Slip HOLD BLOCK as non-flammable and non-corrosive, it also warns that prolonged contact may cause skin or eye irritation. Appropriate protective gloves, goggles, and respiratory protection as required by the SDS should therefore be used during handling and spraying. Avoid spraying directly onto skin or eyes and avoid inhaling spray mist.
Always follow the latest SDS, Technical Data Sheet, vessel procedures, application instructions before use.
PRELOAD Slip HOLD BLOCK is a specialized water-based temporary cargo hold protective coating designed for vessels transporting difficult-to-clean and potentially corrosive bulk cargoes. Its ability to form a thin protective film and subsequently be removed with water makes it a practical solution for cargo hold protection and cleaning preparation.
For vessels carrying cement, sulphur, salt, petcoke, coal, and mineral concentrates, PRELOAD Slip HOLD BLOCK can help protect cargo-hold surfaces, reduce cargo penetration, and simplify post-cargo cleaning operations.
PRELOAD Slip HOLD BLOCK, PRELOAD Slip HOLD BLOCK Marine Chemical, PRELOAD Slip HOLD BLOCK Cargo Hold Coating, RXSOL Preload Supplier, PRELOAD Slip HOLD BLOCK Manufacturer, PRELOAD Slip HOLD BLOCK Hold Block, Cargo Hold Protective Coating, Cargo Hold Barrier Coating, Marine Cargo Hold Coating, Ship Hold Protective Coating, Bulk Carrier Hold Coating, Cargo Hold Cleaning Chemical, Petcoke Cargo Hold Protection, Coal Cargo Hold Coating, Cement Cargo Hold Protection, Sulphur Cargo Hold Protection, Salt Cargo Hold Protection, Marine Chemicals Supplier, Ship Cleaning Chemicals, Cargo Hold Protection Chemical.
Muscat, Salalah, Sohar, Duqm, Rustaq, Barka, Sanaiya, Sur, Seeb, Shinas, Nizwa, Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Fujairah, Sharjah, Umm Al Quwain, Ruwais, Khalifa Port, Jebel Ali, DP WORLD, and all UAE ports...