Before you remove stains and uses of Muriatic make sure to thoroughly protect yourself. personnel involved must wear full “Personal Protective Equipment”. using a designated cleaning kit.

SAFETY AND HANDLING

For degreasing and removal of residues of mimerals oil , coal stain and soot from surface.

Safety Phrases
S-2 Keep out of the reach of children.
S-26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S-36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S-45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible).

Not suitable for use with soft metal like aluminium, magnesium and zinc silicate coatings.

All chemical products should be handled with care. Protective clothing and respiratory equipment should be used where necessary.

Other Valuable Products for Marine - SHIP industries- 

Lime Remover HD  is formulated with strong Surfactant agents and special corrosion inhibitors, sufficient acidic effect enough to neutralize strong alkali content of lime, which makes LIME OUT from deposited surface.

Safety And Handling :-

“RXSOL-22-2201-210” is completely safe to handle, being non-toxic & non corrosive.As with all chemicals general safety and handling procedures apply. Avoid contact with eyes as irritation may occur. Do not take internally. In case of contact with eyes, flush eyes immediately and cupiously with clean running water for 15- minutes and seek medical attention.

For degreasing and removal of residues of minerals oil, coal stain and soot from the surface.

Safety Phrases
S-2 Keep out of the reach of children.
S-26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S-36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S-45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible).

HBI at Elevated Temperatures
The Master of the ship must notify the port authorities if hydrogen gas is detected in the ship holds or if abnormal temperatures are measured in the HBI cargo holds. The Harbor Master and qualified personnel are responsible for executing the action plan when a ship or barge arrives with HBI at the following temperature levels:

A. Greater Than 65° Celsius but Less Than or Equal to 80° Celsius
Proceed with the following actions:
1 > Before unloading the vessel, measure the HBI temperature in each hold and record the measurements in the temperature log book.
2 >  Unload the holds in the assigned zone and immediately transfer the HBI to the storage yard zone as described in PART II, Section 5.4 of this guide.

B. Temperature Greater Than 80° Celsius and Less Than or Equal to 150°
Celsius
Proceed with the following actions:
1 > Before unloading the vessel, measure the HBI temperature in each hold and record the measurements in the temperature log book. This should be done every two hours while the contingency is in effect.
2 >  Unload the holds with HBI at temperature less than 65º Celsius first, then those containing HBI between 65º and 100º Celsius. Continue unloading HBI with temperatures between 100º and 150º Celsius in the
first transfer station, using the movement sense of the belt as a
reference.
3 >  Transfer the HBI from the unloading zone clean and free of debris and flammable material, such as coal, coke and wood to the storage yard indicated by the client as follows:
Transfer the HBI during a maximum of three-minute intervals, and dose (i.e., mix the hotter with the cooler material to have an average temperature lower than the hottest one – no water to be used) the HBI that is at temperatures between 100° and 150° Celsius with cooler material for a maximum of two minutes. Stop the vibrating feeders for about five minutes, but keep the conveyor belts in motion. Repeat these steps until finished with HBI removal. While transferring the HBI, inspect the belt transfer system for any sign of overheating. In case of belt overheating, stop the HBI dosing and transfer but keep the transfer belts in motion until they cool. Take special care to avoid pouring water into hoppers and other equipment. Use a front-end loader to spread the HBI to a level of approximate 30 centimeter height to stop the reoxidation,  Verify that the belts are cooled down and resume HBI transfer per
the previous instructions.


C . Greater than 150° Celsius
Proceed with the following actions:
1 > Before unloading the holds, measure the HBI temperature in each hold and record the measurements in the temperature log book. This should be done every two hours while the contingency is in effect.
2 > Position the HBI with temperatures greater than 150° Celsius at the end of the reception area and spray with pressurized water. In this case, there is no option but to momentarily cool down the HBI.
3 >  When the temperature is reduced to between 80º and 150° Celsius proceed with the steps described in 6.3.2.2. Caution: Do not spray water on hot HBI that is steaming (i.e., emitting water vapor). 

Procedure If Hydrogen Concentration Is Over 1% (25% LEL)
1 > Inform the shipper immediately and seek expert advice.
2 > Keep the natural surface ventilation open at all times
3 > Monitor LEL in the holds continuously until level drops to less than 25 %.
4 > Avoid any possible ignition source on the vicinity.
5 > Care shall be taken as to prevent any spark generation.
6 > Monitor the hydrogen concentration in the holds and keep the surface ventilation (either natural or mechanical) until values fall below 1%.
7 > When hydrogen levels are within safe values, proceed as normal.
8 > On the contrary, additional ventilation should be applied to the space if available and re-testing should be conducted after a suitable interval.
9 > Contact the P & I Club and Shipper and follow the instructions of the appointed expert or surveyor.
10 > At sea, do not open the troubled hold without explicit instructions from the shipper or appointed expert or surveyor.
11 > Ensure there are no possible sources of ignition near the cargo spaces, adjacent spaces or open decks.

RXSOL-20-2059-025  is an all purpose degreaser for cleaning of Oil and Sludge with emulsifiers. It is an excellent blend of powerful cleaner and emulsifying inorganic products .Specially designed  for engine room, degreasing of metal and cargo  tank cleaning .Main feature of this product is, it finally dissociate slop emulsion  to separate oil and water and inhibit calcium, magnesium, and silica scale and also help corrosion control by dispersing iron oxide.

Alkaline cleaning agents contain strong bases for mainstay of industrial cleaning. Cleaners are many in number and vary in type and formulation. Working solutions of alkaline cleaners have proprietary alkaline cleaners and specifically formulated chemical blends. This product is classified as Alkaline Degreasers and Cleaners.